logo
স্বাগতম CHINA NATIONAL HEAVY DUTY INDUSTRY GROUP LIMITED
+86-13210598479

Loading an Excavator on a Low Bed Trailer: Ramp Angle, Deck Height, Lashing and Permit Checks

2026/11/20
সর্বশেষ কোম্পানির ব্লগ সম্পর্কে Loading an Excavator on a Low Bed Trailer: Ramp Angle, Deck Height, Lashing and Permit Checks
Loading an Excavator on a Low Bed Trailer: Ramp Angle, Deck Height, Lashing and Permit Checks

Most low bed trailer problems are not steel problems. They start on the day the machine is driven up the ramp: too steep an approach, the bucket catching the deck edge, chains hooked to a hydraulic cylinder instead of the chassis, or a deck that was widened for the load and never checked against the permit. By the time the trailer is on the road, the damage is already done.

These notes come from the yard, where we load excavators and wheel loaders onto 13 m low beds and detachable goosenecks before every shipment, and from the claims that came back from customers who skipped a step.

Start with the geometry, not the tonnage

A 20 t excavator on a 60 t trailer is not automatically safe. What decides the job is the angle between the ramp and the ground, and the height of the deck edge above the ground with the trailer coupled and loaded.

Two numbers to measure before you order anything:

  • Deck height loaded. Measure at the rear edge with the tractor coupled and the suspension at ride height. It moves with load and with suspension type, so measure it loaded, not empty.
  • Ramp angle. A folding hydraulic ramp runs comfortably at 12–15°. Past about 18° the machine's dozer blade or the back of the track frame starts to foul the deck, and the operator is climbing on the throttle instead of the geometry.

On our 13 m unit the deck is 13,000 * 3,000 mm with 5 mm patterned plate. The pattern is not decoration — it is what stops a steel track from sliding sideways when the machine turns on the deck in the rain.

Three deck formats, three different jobs

FormatWhat it is good atWhere it costs you
Fixed low bed, 13 m * 3 m, 60 tExcavators, rollers, small crushers; lowest cost per tonNo width margin; oversize blades need a permit and often a second trailer
Widening low bed with double-section hydraulic rampLoads that are 3.0–3.4 m wide; ramp folds to clear the ground on site roadsHydraulic circuit and remote to maintain; slightly heavier
Removable gooseneck, 70 tTall machines and front-loading; the gooseneck becomes the rampNeeds a diesel power pack and a driver trained on the detach sequence

The widening version adds 200 mm per side, so 3.0 m on the road becomes 3.4 m for the load. That is enough for most 20–25 t excavators with a wide pad, and it keeps you legal for normal running.

The gooseneck is a different animal: 15,690 * 3,200 * 1,800 mm overall, 6,700 * 3,200 mm platform, three 16 t axles, 3.5 inch 90# bolt-in kingpin, 12 * 12R22.5 on 9.00-22.5 rims, spring suspension and a WABCO RE-6 emergency relay valve. It carries 70 t and loads from the front, which is the only practical way to put a tall machine on a deck that sits low.

Payload math that survives a weight bridge

Trailer ratings are payload, not gross. On a three-axle 60 t low bed with 13 t axles, the axles carry roughly 39 t, and the rest of the load goes through the kingpin onto the tractor. If you put a 60 t machine on it and assume the trailer "is rated for 60 t", you will be over on the drive axles and probably over on the trailer axles as well.

  • Ask for the tare weight of the exact build, then subtract it from the rated payload.
  • Check the kingpin load limit of the tractor, not just the trailer.
  • For 80–120 t machinery, move to four axles and a heavier beam rather than adding tyres to a three-axle frame.

Machine plus bucket, plus a spare bucket on the deck, plus the operator's toolboxes — weigh the whole thing. The scale at the port does not care what the brochure said.

Lashing: four points, on the chassis, never on a cylinder

Grade 80 chain, 10 mm, with load binders, four points minimum: two at the front of the track frame, two at the rear, crossed where the deck allows. Hook to the trailer's D-rings or stake pockets, never to the machine's bucket cylinder, boom cylinder or a hydraulic hose guard.

Over the tracks, not over the hydraulic lines. Put a friction mat under steel tracks if the deck is painted rather than patterned. Re-check tension after the first 20 km — chain settles, and a slack chain at 80 km/h is a projectile.

Width, height and permits

At 3.4 m widened you are usually inside a standard oversize permit in most markets; a 4.5 m blade or a machine over 4.2 m tall is not, and needs route survey, escort and often a night movement. Height is the number people forget: machine height plus deck height, measured, not estimated from the spec sheet.

If the route has bridges or overhead lines, the gooseneck format buys you height because the deck sits lower and the machine loads from the front. If the route has weight limits, the extra axle matters more than the deck format.

Yard checklist before the machine goes on

  1. Trailer coupled, kingpin locked, landing gear fully raised, air lines connected, brake test done.
  2. Ramp fully deployed and pinned; hydraulic hoses clear of the fold line.
  3. Deck swept, no gravel or ice under the tracks.
  4. Widening plates locked in the position you will travel in.
  5. Machine tracks or tyres clean, bucket curled and pinned.
  6. Four chains on, binders tight, no chain over a hydraulic line.
  7. Total height measured with a tape, written on the dispatch note.
  8. Photo of the lashing pattern sent to the customer before departure.

Every trailer we ship gets a full wax spray before loading onto the vessel. On a RoRo or bulk-ship passage that coating is the difference between a trailer that arrives with a clean chassis and one that arrives with rust blooms in the rails.

FAQ

Can a 60 t low bed carry a 60 t excavator?

No. The rating is payload and the tare weight comes off it, plus part of the load sits on the tractor. Work from the actual tare of the build.

Mechanical or hydraulic ramp?

Mechanical for a fixed site where the ground is flat and the ramp angle is known. Hydraulic folding for mixed sites, rented yards, and any machine that needs a gentle approach angle.

Is a widening deck worth it?

If more than a third of your loads are 3.0–3.4 m wide, yes. It avoids a second trailer and a permit on the majority of jobs.

How often should the hydraulic ramp be serviced?

Check hoses and pins every 250 h, change the filter at the first 50 h and then annually, and keep the remote control in the cab, not in the toolbox where it gets crushed.

The short version

Measure the deck height loaded, keep the ramp at 12–15°, do the payload math with the real tare, chain to the chassis in four points, and check the width and height against the permit before you leave the yard. The trailer is the easy part; the loading is where the money is lost.

Send us the machine model, its weight with attachments, and the route, and we will tell you whether a 13 m fixed deck, a widening deck or a removable gooseneck is the right answer for the next three years rather than the next load.